🌍 JLmagnet Since 2006 ⭐ 20+ Year Industry Experience ✓ Verified Elite Supplier
✓ Verified Elite Supplier
Menu

Multipole Ring Magnet Guide: Orientation and Grade Selection

Author: HTNXT-Benjamin Hughes-Electrical & Electronics Release time: 2026-11-18 02:18:54 View number: 17

A sintered NdFeB ring magnet is specified through two separate decisions. The first is the product form: a multipole ring carrying a repeating pattern of alternating poles, or a radial ring magnetized through the wall. The second is the material decision: the grade plus its thermal class. The product form fixes pole count, magnetization direction and the way the ring is mounted; the grade fixes how much flux the ring produces and how much heat it can accept before its working point fails. A drawing that names only the geometry leaves both decisions open, and two suppliers can then quote the same ring and deliver different magnets.

This guide is written for motor designers, mechanical engineers and procurement teams who are past the first enquiry and need a specification that can be quoted, sampled and approved. It separates multipole and radial ring product forms, sets out how grade and thermal class are chosen together, uses the verified N52 D20x10x5 mm sintered ring record as a worked example, and closes with the items a design team must confirm when the magnet supplier's IATF 16949 certificate excludes product design under Chapter 8.3.

Sintered NdFeB radial ring magnet used as a reference part for orientation and grade specification

A sintered NdFeB ring: the geometry is only half of the specification. Magnetization pattern and grade must be fixed on the same drawing.

Three Gaps That Appear Before the First Sample

Ring magnet projects rarely fail because of poor sintering. They fail because the purchase specification does not contain the information the supplier needs to build the part the design intended. Three specific gaps account for most of the rework.

The form gap. A 20 mm outside-diameter sintered ring can be supplied as a radially oriented ring with two poles, as a single piece magnetized into eight alternating poles on the outer face, or as a set of pressed segments mounted into a ring assembly. Each behaves differently in the same motor, yet none of those differences appears in a dimensional tolerance block. The part measures correctly, incoming inspection passes, and the air-gap flux still does not match the simulation.

The thermal gap. Grade designations such as N42SH pack two answers into one token: N42 is the nominal energy-product class, and SH is the coercivity and temperature class. Teams often select on the first number and discover the second only after a hot soak test. A magnet that loses part of its magnetization at operating temperature does not recover it when the assembly cools.

The responsibility gap. In automotive programmes, the supplier's quality certificate may cover manufacturing only. When product design under IATF 16949 Chapter 8.3 is excluded from the scope, the design record has to come from the buyer's side of the table. Projects that assume the magnet supplier owns the magnetic design can reach PPAP with no owner for the design validation evidence.

The rest of this guide resolves those three gaps in order: product form first, then grade and thermal class, then the contractual boundary.

Where Multipole and Radial Rings Sit in the Magnet Supply Chain

Ring magnets are a mature product category, but the capability to make them is concentrated. China accounted for roughly 94% of global sintered permanent magnet production in 2024, according to the International Energy Agency's rare-earth analysis. For a European, North American or Asian buyer, that concentration means the difference between suppliers is rarely the base material; it is the orientation technology, the magnetizing fixtures and the inspection discipline behind the specific ring form.

Not every sintered NdFeB plant offers multipole and radial orientation as production processes. A press that produces radially oriented rings needs different tooling from one producing blocks, and a multipole ring adds a magnetizing fixture whose design determines the pole pattern the customer receives. Buyers who compare only grade and price can end up with a supplier that subcontracts the magnetization step, which moves pole-pattern control outside the certified process.

Ningbo Jinlun Magnet Technology Co., Ltd. is a Chinese sintered NdFeB manufacturer established in 1996 and incorporated in 2006, operating from Cixi in Zhejiang with an annual production capacity of about 8,000 tonnes and approximately 400 employees. Its stated product range covers multipolar rings, radial rings and Halbach assemblies as well as blocks, discs, arcs, trapezoids and custom shapes, and its mass-production grades include the SH, UH, EH and AH high-temperature series. The company also runs in-house machining and multi-process surface treatment, which matters for ring projects because the coating and the final dimensions are usually the last two characteristics to be approved.

Separating the Two Ring Product Forms

The radial ring: one magnetization axis through the wall

A radially oriented ring is magnetized along a single axis that crosses the ring wall, so one pole appears on the outer diameter and the opposite pole on the bore. The orientation direction is established during pressing, which means the tooling — not the magnetizing fixture — decides whether the part is truly radial. This form suits any function where flux has to cross the wall into a mating component: a rotor ring acting on a stator, a sensor ring acting on a Hall element, or a coupling ring acting across a containment barrier.

Two characteristics dominate quality on this form. The first is wall uniformity and concentricity between bore and outer diameter, because a radial ring with an eccentric wall produces an uneven flux distribution that no downstream sorting can correct. The second is the working point of the actual geometry: a thin wall in an open magnetic circuit operates on a low permeance load line, and it demagnetizes at a lower temperature than the same grade in a thick, well-shielded section. Radial magnetization is also not the same as diametral magnetization, a distinction worth writing into the drawing so a quotation is not built on the wrong orientation.

The multipole ring: poles repeated around the circumference

A multipole ring carries several alternating pole pairs around its circumference or across an end face. As the ring rotates or as a sensor passes it, the field alternates, which is why this form appears in compact motors, actuators and position-sensing assemblies where pole count effectively sets the electrical frequency of the design. The magnetization pattern — radial, multipole or Halbach — is a separate specification from the ring dimensions, and the pole count, pole arc and transition zone between poles belong on the drawing.

There are two production routes to a multipole ring, and they are not interchangeable. The first is a single sintered ring oriented during pressing and then magnetized into a pole pattern with a dedicated fixture; the fixture defines the field the customer receives, so fixture control is a quality characteristic in its own right. The second is a segment assembly, where discrete sintered segments are mounted or bonded into a ring, which is the usual route for large diameters or for stator mounting, where individual segments are easier to handle and to fasten. A segment assembly adds interfaces and tolerance stack, but it removes the size limit that single-piece pressing imposes.

Bonded neodymium is sometimes proposed for thin, complex multipole geometries because it can be moulded rather than pressed and machined. It is a different material class with lower magnetic output than sintered NdFeB, so it cannot be substituted into an existing magnetic circuit without re-checking the flux budget and the thermal margin.

Precision measurement system used to verify magnetic properties of sintered NdFeB ring magnets

Magnetic-property verification on sintered NdFeB material. Ring acceptance should reference measured Br, Hcj and (BH)max, not the nominal grade alone.

Grade and Thermal Class Are Two Different Lines on the Drawing

In the NdFeB designation system, the number and the letters answer different questions. The number — N35 through the high N50s, a range the manufacturer describes as 35 to 58 MGOe for commercial sintered NdFeB — is the nominal maximum energy product, a measure of flux output. The suffix letters define the coercivity class, which sets the temperature at which the magnet resists demagnetization. A specification that states N52 without a temperature class has answered only the first question.

ClassTypical maximum operating temperatureWhat the class means in practice
NUp to 80 °CBaseline class; the highest energy products sit here
HUp to 120 °CRaised coercivity for warmer assemblies
SHUp to 150 °CCommon class for sustained motor and actuator duty
UHUp to 180 °CHigher coercivity where the rotor runs hot
EHUp to 200 °CReached with grain-boundary diffusion processing
AHUp to 220 °CExtreme margin; 220 °C figure from third-party product data, confirm with the supplier's hot curve

The operating-temperature figures above are class ceilings, not guarantees for a specific part. The temperature a ring can survive depends on the permeance of the circuit it sits in — the geometry, the air gap and the surrounding steel all change the load line — so the correct verification is the demagnetization curve at the operating temperature, not the room-temperature datasheet. This is the single most useful instruction in this guide: ask for the hot curve and check the working point of your actual ring, not the grade's headline number.

Grain-boundary diffusion is the process that makes the EH class practical in production. The manufacturer states that its diffusion process raises coercivity by 5 to 10 kOe while using less than 0.6 wt% heavy rare earth, which is how a 200 °C EH grade is reached without the full heavy-rare-earth loading of a conventional alloy. For buyers managing rare-earth supply and export-control exposure, the same supplier also offers heavy-rare-earth-free formulations with less than 0.1% heavy rare earth, described as stable from −50 °C to 150 °C. That option trades some thermal ceiling for a lower regulatory exposure, and it should be evaluated against the real operating temperature rather than rejected or accepted by default.

Coating is a third, separate line. It protects against corrosion and does not raise the thermal class, but it must be specified at the same time because plating thickness affects the final dimensions and because automotive or outdoor duty usually requires salt-spray evidence. The manufacturer offers bright and matte NiCuNi, single-layer nickel, black oxide, colour zinc, chemical nickel and epoxy systems, with in-house plating and salt-spray and high-temperature ageing tests used as part of qualification.

Worked Example: The N52 D20x10x5 mm Sintered Ring

The verified product record for this supplier lists a sintered neodymium magnet as N52 D20x10x5 mm — grade N52 in a ring envelope of 20 mm, 10 mm and 5 mm. It is a useful example precisely because it is a high grade in a small, thin-walled form, which is where grade and thermal decisions collide.

N52 sits at the high end of the N series, so it delivers the most flux per millimetre of magnet in that family. It also carries the least thermal headroom: standard N grades are rated to about 80 °C. In a cool, well-ventilated assembly with a good permeance, that is an efficient choice. In a housing that reaches 100 °C or more, the same ring is outside its class, and the specification has to move to SH (150 °C), UH (180 °C) or EH (200 °C) depending on the measured temperature and the load line of the ring in its circuit.

That move is not free. Coercivity is raised through alloying or grain-boundary diffusion, and the highest energy-product numbers and the highest thermal classes rarely coincide in one grade. A design that needs both usually has to trade envelope or flux — a slightly larger ring, a thicker wall, or a lower energy-product class with the required thermal margin — and then re-check the magnetic circuit. Treating N52 as a default and EH as an upgrade misses the point: they are answers to different operating conditions, not quality tiers.

The dimensional string in that record also shows why the drawing matters. The supplier's naming code combines a shape letter with dimensions — D for disc or column, F for block, R for arc — with rings written in the form D15×D5×25 and features such as bores appended after a dash, for example D50×D13.5×20-D20×8 for a ring with a counterbore. For a part recorded as 20 × 10 × 5 mm, the drawing must state explicitly which value is the outer diameter, which is the bore and which is the axial height. Leaving that allocation to interpretation is how a radial ring arrives with the wrong wall thickness.

Specification Sequence: From Magnetic Requirement to Purchase Order

The following sequence keeps the form decision and the material decision in the right order. It is written for a project that is already in evaluation or execution, where the magnetic function is broadly known and the task is to lock a specification that can be quoted and approved.

  1. State the magnetic function before the shape. Describe what the ring must do — cross a gap into a stator, alternate poles past a sensor, hold torque across a coupling wall — and let that description select the product form. A form chosen because a similar part existed elsewhere is the most common source of rework.
  2. Fix the magnetization pattern and pole geometry. For a multipole ring, write the pole count, the face that carries the poles (outer diameter, bore or end face), the pole arc and the acceptable transition zone. For a radial ring, state that the orientation is through the wall and confirm it is not a diametral request. Both forms need the magnetization direction stated on the drawing, because the fixture is built from that line.
  3. Lock the mechanical envelope and the datums. Give outer diameter, bore, axial height, wall thickness, concentricity, chamfers and any step or counterbore, and identify which surface is the assembly datum. Wall thickness deserves its own tolerance: it sets the working point of a radial ring and the segment fit of an assembly.
  4. Select the grade from the flux requirement, then test it against temperature. Choose the energy-product class that meets the air-gap flux target with the available envelope, then check that grade's demagnetization curve at the maximum operating temperature using the permeance of the real circuit. If the working point is marginal, change class before changing dimensions.
  5. Set the thermal class with margin, and record the evidence. Where measured or expected temperatures approach the class ceiling, specify EH (200 °C) or higher and require the hot curve as a submission document. Do not accept a room-temperature datasheet as thermal evidence for a part that runs hot.
  6. Specify coating and its acceptance test. Name the coating system, the thickness range and the corrosion test required. This is the step where automotive and outdoor programmes usually add salt-spray and adhesion requirements, and it must be settled before tooling because plating thickness changes the finished dimension.
  7. Define lot acceptance, not only first-article acceptance. Require magnetic property reports for Br, Hcj and (BH)max per lot, dimensional inspection against the drawing, and a stated batch-consistency expectation. For reference, this supplier states magnetic performance fluctuation within ±2% and a key dimensional pass rate of 99.5%, with a test report shipped per batch or lot — useful benchmarks to write into a technical agreement rather than assumptions to carry silently.
  8. Agree who owns the design. Before the first sample, confirm which party holds design authority for the magnetic requirement and the validation plan. The next section explains why this step cannot be left to the purchase order.
Vision measuring instrument inspecting dimensional tolerances of sintered NdFeB ring magnets

Dimensional inspection on a vision measuring instrument. Bore, wall thickness and concentricity should each be tolerance-controlled on a ring drawing.

When the IATF 16949 Scope Excludes Product Design Under Chapter 8.3

The supplier's automotive certificate states its boundary openly. Certificate 12 111 69512 TMS (IATF Cert. No. 0576974, USI L2S2NA), issued by TÜV SÜD Management Service GmbH and valid from 4 July 2025 to 3 July 2028, covers manufacturing of material and products for sintered neodymium iron boron permanent magnets, without product design as per Chapter 8.3. That parenthetical is not a weakness in the certificate; it is a definition of where the supplier's certified responsibility stops.

The practical meaning is straightforward. The certified quality management system covers the manufacturing processes that turn a controlled drawing into a conforming magnet. Product design and development — the design record, the tolerances, the magnetic requirement and the design validation plan — must originate with the customer or another design-responsible party. This is a normal arrangement for a component supplier working to a customer drawing, and it works well as long as the design inputs are controlled documents rather than email attachments.

Design teams should confirm the following six items before a ring magnet programme enters PPAP:

  • Design authority. Name the party that signs the drawing and owns the design record, and record it in the technical agreement. If that party is the customer, the supplier is a build-to-print manufacturer for the magnetic element.
  • Controlled design inputs. The magnetic requirement — pole pattern, flux target, maximum operating temperature, duty cycle — must enter the supplier's process as a released specification. Verbal targets cannot be validated later.
  • Validation ownership. Agree who runs design validation and who accepts the consequence if the ring meets the drawing but the motor does not meet its performance target. Under a Chapter 8.3 exclusion, that responsibility does not sit with the magnet manufacturer's certified system.
  • Feasibility and special characteristics. Ask the supplier to confirm manufacturability against the drawing and to identify the characteristics it will control in its process FMEA and control plan — wall thickness, pole symmetry, coating thickness or magnetizing fixture parameters.
  • Change notification. Fix the notification window for changes to grade, powder source, coating, magnetizing fixture or machining process, and state which changes require customer approval before shipment.
  • Design support as a separate service. Magnetic-circuit simulation, field analysis and material-selection optimisation are available from the supplier as engineering services, but they sit outside the certified design scope. Their outputs must be reviewed and released by the design-responsible party.

Two points are frequently misread. First, the exclusion does not mean the supplier cannot support design work; it means the certificate does not cover it, so the responsibility has to be assigned deliberately. Second, manufacturing-scope evidence remains fully usable: IATF 16949 certification, PPAP capability and per-batch magnetic property reports can all be requested for the production scope. The supplier's wider system also includes ISO 9001:2015 certification issued by TÜV SÜD (valid to 3 July 2028) and ISO 14001:2015 environmental certification valid to 17 January 2027, which cover the quality and environmental management layers around the automotive scope.

IATF 16949:2016 certificate for sintered NdFeB magnet manufacturing with product design excluded under Chapter 8.3

The automotive certificate scope states manufacturing of sintered NdFeB materials and products without product design under Chapter 8.3.

Where Each Ring Form Fits

Application notes help a team sanity-check a form decision, provided they are read as fit criteria rather than performance promises.

Automotive drive motors and electric power steering. These programmes combine high-coercivity grades with tight dimensional control and a documented thermal margin. Arc and segment forms are common where the rotor or stator is built from discrete pieces, and the specification emphasis falls on pole geometry, batch consistency and the hot demagnetization curve. This is also the segment where the Chapter 8.3 boundary matters most, because design validation is usually owned by the tier-one or the vehicle manufacturer.

Servo motors and compact actuators. A single-piece multipole ring saves axial space and removes the assembly stack of individual segments, which is why servo and actuator designs use it where the rotor diameter allows. The trade-off is fixture dependence: the pole pattern is only as repeatable as the magnetizing fixture, so fixture control belongs in the quality agreement.

Wind turbine generators and large-diameter machines. Diameter pushes the design toward segment assemblies, since single-piece pressing and sintering become impractical at large sizes. For context on material intensity, one commercial research estimate puts offshore wind demand at roughly 200 to 600 kg of high-performance NdFeB per megawatt, which is why grade efficiency and supply continuity are usually weighed together on these projects.

Elevator traction machines. Rotor magnets here are specified for dimensional repeatability and consistent magnetic output across many units, because the assembly is replicated rather than prototyped. Batch-to-batch stability matters more than the last increment of energy product.

Magnetic couplings. Custom radial rings and multipole assemblies transmit torque across a containment wall without contact, so the pole count and the gap define the torque density, and the magnetization pattern must be specified with the same precision as the dimensions.

Sensors and position feedback. Multipole sensor rings convert rotation into a periodic field, and the pole transition zone is often more critical than the peak flux. Draw the transition tolerance explicitly; it is frequently missing.

Comparison: Multipole Ring, Radial Ring and Segment Assembly

Specification pointMultipole ring, single pieceRadially oriented ringSegment / arc assembly
MagnetizationAlternating poles around the circumference or on an end faceOne through-wall axis, pole on outer diameter and boreSet by segment orientation and mounting
Pole countDefined by the magnetizing fixture and fixed on the drawingNormally twoDetermined by the number of segments and their orientation
Tooling dependencePressing tool plus dedicated magnetizing fixtureOrientation fixed during pressingPressing tool per segment plus assembly fixture
Inspection focusPole pattern, symmetry, transition zones, flux per poleWall uniformity, concentricity, flux across the wallSegment dimensions, orientation control, cumulative tolerance
Main technical riskPole definition missing from the drawingThin wall lowering the working pointInterface and tolerance stack during mounting
Typical fitCompact motors, actuators, sensor ringsMotors, couplings and sensors needing through-wall fluxLarge diameters, stator mounting, high pole counts

Frequently Asked Questions

Does the IATF 16949 certificate cover magnet design?

No. The certificate scope for this supplier covers manufacturing of material and products for sintered NdFeB permanent magnets and explicitly excludes product design as per Chapter 8.3. The design record, tolerances and validation plan must therefore come from the customer or another design-responsible party, while the certified system covers the manufacturing processes that realise the drawing.

Can one supplier deliver both multipole rings and radially magnetized rings?

Yes, where the factory runs both orientation technologies as production processes rather than subcontracting them. This manufacturer states that it uses multipolar and radial orientation to produce multipole rings and radial rings for motors, sensors and actuators, and that custom magnetization patterns including radial, multipole and Halbach are available. Pole count, magnetization direction and tolerance requirements should be confirmed on the drawing at the tooling stage, because the fixture is developed from those parameters.

Which grade suits a ring that runs hot: N52, N42SH or N48EH?

The operating temperature decides, not the energy product. N grades, including N52, are rated to about 80 °C; SH reaches 150 °C; EH reaches 200 °C with grain-boundary-diffused material. The verified N52 D20x10x5 mm ring suits a cool assembly with good permeance, while a housing above roughly 80 °C calls for an SH, UH or EH class and a re-check of the working point on the hot demagnetization curve.

Is this an OEM sintered N52 neodymium magnet manufacturer?

Yes. The manufacturer provides ODM production services for sintered neodymium magnets, including custom sintered NdFeB magnet components, with customizable material grades, magnetic specifications, shape and size, machining tolerances, and surface treatments such as nickel, zinc and copper plating. Its product record includes the N52 D20x10x5 mm sintered ring, alongside ring, arc, block, trapezoid and custom shapes in SH, UH, EH and AH series.

What is the minimum order quantity and how are samples handled?

The stated minimum order quantity is 10 kg for standard production, with sample orders excluded from that minimum and confirmed as needed. Samples are quoted separately against the specific grade, coating and magnetization requirement, which is why the drawing should be complete before a sample request is raised — a multipole ring sampled against an incomplete pole definition usually has to be re-tooled.

What lead time should be planned for a ring magnet order?

Regular batch lead time is quoted at about 25 days, subject to grade, shape complexity, coating and magnetization requirement, with sample timing confirmed per request. Because multipole and radial rings both depend on tooling, the first order should be planned with a tooling allowance before the batch clock starts. Sharing the drawing, target quantity and operating temperature with the supplier at the enquiry stage is the most reliable way to get a schedule that holds.

Conclusion

Ring magnet specification becomes manageable once the questions are separated. The product form — multipole ring, radial ring or segment assembly — is a magnetization and assembly decision that belongs on the drawing with pole count, direction and transition tolerance. The grade and thermal class are a materials decision that must be validated against the hot demagnetization curve of the actual geometry, not against a room-temperature datasheet. The N52 D20x10x5 mm ring and the EH class rated to 200 °C are simply two points on the same decision line, chosen for different operating conditions.

The last item is procedural rather than technical. When the supplier's IATF 16949 scope excludes product design under Chapter 8.3, the design record and its validation belong to the buyer's side of the programme, and the supplier's certified responsibility begins with manufacturing. Confirming that split before tooling is cheaper than discovering it during PPAP.

Ningbo Jinlun Magnet Technology Co., Ltd. publishes its capability profile, grade range and certification scope through jlmagnet.com. Design teams that want to review the manufacturing and testing base before a technical discussion can download the JLmagnet company profile (PDF), and can send a ring drawing with grade, operating temperature and pole requirement to Sales00@jlmagnet.com for a manufacturability review.

JLmagnet sintered NdFeB magnet manufacturing and product reference for ring magnet enquiries

Ring magnet enquiries are most useful when the drawing already states product form, grade, thermal class and coating.

Have Questions or Need More Details?

Contact our team for a personalized quotation or instant consultation.

Request a Quotation

Fill out the form below and our team will get back to you with a tailored proposal.

Attach images, files, or documents.

We'll respond within 24 hours (Mon–Sat).

WhatsApp Direct Chat

Prefer to chat in real-time? Message us on WhatsApp for instant assistance & quick answers.

  • Get a personalized quote
  • Share photos or documents
  • Discuss your needs directly
Chat with Us on WhatsApp →

Typically replies in 5–30 minutes during business hours.

Support: Images, videos, PDF
Latest