🌍 JLmagnet Since 2006 ⭐ 20+ Year Industry Experience ✓ Verified Elite Supplier
✓ Verified Elite Supplier
Menu

Multipole Ring Magnets Explained: Sintered NdFeB Basics for Engineers

Author: JLmagnet Release time: 2026-10-28 03:52:34 View number: 50

A multipole ring magnet is a one-piece sintered NdFeB ring whose circumference carries several alternating north and south poles instead of a single pole pair across the diameter. For an engineer specifying one for the first time, the definition matters less than the three variables it forces you to fix early: the pole pattern, the thermal grade, and the mechanical tolerance of the ring.

This guide explains where multipole and radially oriented ring magnets sit inside the sintered NdFeB family, uses the N52 D20 × 10 × 5 mm ring magnet as a worked example of how to read a datasheet from ambient up to mid-high temperature, and then connects those basics to motor and medical device designs.

Sintered NdFeB ring magnet D20 x d10 x 4 mm, the base geometry used for radially oriented and multipole ring designs
Sintered NdFeB ring magnet, D20 × d10 × 4 mm. Ring geometry is the starting point for both radially oriented and multipole designs.

Problem Definition: Why Ring Magnets Get Re-Quoted

Ring magnets are among the most frequently re-quoted items on a motor bill of material, and the cause is usually a drawing that specifies geometry but not magnetics. Four items are routinely left open.

  1. Pole pattern. 'Radially magnetized' describes the field direction through the ring wall. It does not state how many poles run around the circumference, and an 8-pole and a 12-pole ring are different parts even when the outer dimensions match.
  2. Thermal grade. The same ring dimensions can be produced in several grades with different maximum working temperatures. The grade, not the shape, decides whether the ring operates comfortably at 120 °C or at 180 °C.
  3. Tolerance and concentricity. The multipole and radial rings described in this article are held to ±0.05 mm, while the 45SH arc segment is held to ±0.1 mm. Tolerance class changes machining time, scrap rate and bore-to-shaft fit.
  4. Coating and documentation. Ni-Cu-Ni is the standard coating on the ring types here, with zinc, epoxy and parylene available. The coating choice determines which corrosion and aging tests the supplier has to run, and what paperwork arrives with the batch.

Each open item becomes a clarification round, a new tooling assumption or a price revision. Fixing all four before the RFQ removes most of that loop.

Industry Background: Where Ring Magnets Sit in the Sintered NdFeB Family

Sintered NdFeB is the highest-energy permanent magnet material in routine industrial use, and it is the material behind most traction, servo and spindle rotors built today. Supply is highly concentrated: China accounted for 94% of global sintered permanent magnet production in 2024, according to the International Energy Agency rare-earth analysis. That concentration is one reason supplier documentation carries as much weight as the datasheet.

Grades are named with a letter code attached to the energy product, and each letter maps to a maximum working temperature: N grades at 70–80 °C, M at 100 °C, H at 120 °C, SH at 150 °C, UH at 180 °C and EH at 200 °C, with AH grades quoted up to 220 °C in published third-party references. Across the standard series, JLmagnet covers N25–N58, 33M–56M, 30H–56H, 30SH–56SH, 30UH–54UH, 28EH–48EH and 28AH–42AH, with remanence from 0.96 T to 1.47 T, intrinsic coercivity from ≥12 kOe for N and M grades to ≥30 kOe for EH grades, and maximum energy product from 23 to 53 MGOe.

Shape is where ring magnets separate from the rest of a magnet catalogue. JLmagnet (Ningbo Jinlun Magnet Technology Co., Ltd.) is a sintered NdFeB magnet manufacturer based in Cixi, Ningbo, China, founded in 1996 and incorporated in 2006, producing blocks, discs, rings, arcs, trapezoids, multipole and radial rings, Halbach assemblies and custom shapes. The ring forms are the ones that replace multi-piece segment assemblies inside a rotor.

Radial vs Multipole: What the Words Actually Describe

Radially oriented rings

A radially oriented ring is magnetized so the field direction runs through the ring wall. JLmagnet supplies the type as a 40H OD18 × ID10 × H4 mm ring with 4 or 6 poles, Br > 1.26 T, Hcb > 939 kA/m, Hcj > 1353 kA/m and (BH)max of 302–326 kJ/m³. That specific configuration is rated to 120 °C maximum working temperature, and the grade options run from N42H to N40UH, which extends the ceiling to 180 °C.

Multipole rings

A multipole ring places several pole pairs around the same one-piece body. In the 42H OD25 × ID16 × H5 mm configuration the ring carries 8 or 12 poles, with Br > 1.29 T, Hcb > 963 kA/m, Hcj > 1353 kA/m and (BH)max of 318–342 kJ/m³. That build is rated to 120 °C maximum working temperature, and the design family is available in multiple grades with continuous operating temperature up to 180 °C.

What one-piece construction changes downstream

The engineering argument for either ring type is the same, and it is mechanical more than magnetic:

  • The integrated body has no glued segments, which is the stated basis for superior concentricity and dynamic balance.
  • The field distribution is smooth and sinusoidal, which contributes to low torque ripple and quiet operation.
  • Magnetic consistency between poles is stable from part to part.
  • Rotor assembly is simplified, and the manufacturer positions the one-piece ring as a production-cost saving against an assembled segment rotor.
One-piece multipole sintered NdFeB ring magnet 42H OD25 x ID16 x H5 mm with 8 or 12 poles
One-piece multipole sintered NdFeB ring, 42H OD25 × ID16 × H5 mm, 8/12 poles. No glued segments, so concentricity and pole-to-pole consistency are set by one body.

How to Read a Sintered NdFeB Ring Magnet Datasheet

The five magnetic numbers

  • Br, remanence (T). Available flux density. The N52 D20 × 10 × 5 mm ring is listed at Br > 1.42 T; the 40H radial ring at Br > 1.26 T.
  • Hcb, normal coercivity (kA/m). Resistance to demagnetization in the second quadrant of the curve. It is the weaker of the two coercivity figures and is quoted as > 860 kA/m for the N52 ring and > 995 kA/m for the 45SH segment.
  • Hcj, intrinsic coercivity (kA/m). The number most closely tied to temperature capability. The N52 ring is listed at > 955 kA/m (an N-class value, equivalent to the ≥12 kOe floor), the multipole and radial rings at > 1353 kA/m, and the 45SH segment at > 1592 kA/m.
  • Hk/Hcj, squareness (%). Every product referenced here is listed at > 95%. Squareness describes how abruptly the demagnetization curve reaches its knee; a squarer curve tolerates a working point closer to the knee before irreversible loss begins.
  • (BH)max, energy product (kJ/m³). Overall strength: 398–422 for the N52 ring, 318–342 for the 42H multipole ring, 302–326 for the 40H radial ring, and 342–366 for the 45SH segment.

The four mechanical and surface items

  1. Dimensions, tolerance and concentricity callout — ±0.05 mm for the multipole and radial rings, ±0.1 mm for the 45SH segment.
  2. Magnetization direction and pole count — radial orientation plus the number of poles, not one or the other.
  3. Coating — Ni-Cu-Ni is standard; zinc, nickel, epoxy and parylene are available for different working environments.
  4. Test documentation — magnetic test reports issued per batch, plus salt-spray and high/low-temperature damp-heat aging test capability in-house.

Worked Example: The N52 D20 × 10 × 5 mm Ring Magnet

The N52 ring is the clearest illustration of how flux and thermal headroom trade against each other, because it is the strongest grade in the examples here and also the one with the tightest temperature ceiling.

ParameterListed value — N52 D20 × 10 × 5 mm ring
Material / typeSintered neodymium magnet, ring
ModelN52 D20 × 10 × 5 mm
Br> 1.42 T
Hcb> 860 kA/m
Hcj> 955 kA/m
Hk/Hcj> 95%
(BH)max398–422 kJ/m³
Maximum working temperature80 °C

Read the numbers together. Br > 1.42 T sits near the top of the manufacturer's 0.96–1.47 T range, and 398–422 kJ/m³ is the highest energy product among the configurations in this article. The cost of that flux is thermal headroom: an Hcj of > 955 kA/m is an N-class value and the maximum working temperature is 80 °C.

That places the part firmly in ambient duties, which matches its stated application list: consumer electronics and acoustics, home appliances, industrial automation and general equipment, automotive interior, education and laboratory equipment, plus precision automation and sensing use where the same product is positioned for high-performance motor and sensor work, medical device components and hardware holding.

The design rule that falls out of this is simple. If the calculated magnet temperature in your assembly stays below 80 °C, an N52 ring gives you the most flux per millimetre. If the magnet sits at 100 °C or above — a servo motor under continuous load, a sensor inside a warm enclosure — the same geometry has to move to an H, SH or UH grade, and Br will drop as Hcj rises. The 45SH segment illustrates the other side of that curve: Br > 1.33 T with Hcj > 1592 kA/m and a 150 °C ceiling.

From Ambient to Mid-High Temperature: Choosing the Grade

Grade familyMaximum working temperatureWhere it fits in a ring magnet project
N70–80 °CAmbient duties: consumer electronics, sensors, instrument hardware (N52 ring example)
M100 °CLight thermal load, low-cost motor and actuator designs
H120 °CStandard motor duty: 42H multipole and 40H radial ring configurations are rated at 120 °C
SH150 °CHigher-load motors; 45SH arc segment example
UH180 °CUpper end of the multipole and radial ring range (radial options run N42H to N40UH)
EH200 °CHigh-temperature motor compartments; EH grades are mass-produced in the standard series
AHup to 220 °C (third-party reference)Extreme thermal duty; AH grades are available in the 28AH–42AH range

Two practical notes matter more than the table itself. First, maximum working temperature is a property of the grade, not of the shape, so a 42H multipole ring and a 42H block share the same ceiling. Second, specify against measured magnet temperature rather than housing temperature: the ring sits close to the winding, and surface readings understate what the magnet actually sees.

High and low temperature damp heat aging test chamber used to validate sintered NdFeB magnet thermal stability
High and low temperature damp heat aging test. Thermal grade claims are verified on batches, not only on the certificate of the material.

Coating Choice and Corrosion Protection

Both the multipole and the radial ring use a standard Ni-Cu-Ni coating, which the manufacturer specifies for corrosion resistance and long service life. Zinc, nickel, epoxy and parylene options are available where the working environment is more aggressive, and salt-spray testing is run in-house.

For a ring that is press-fitted or bonded into a rotor, confirm that the coating survives the assembly sequence as well as the operating life. Epoxy and parylene are usually considered when the part is exposed to humidity, salt fog or cleaning chemicals, and the coating must not change the bore tolerance that the ±0.05 mm callout depends on.

Tolerance, Concentricity and Rotor Assembly

The multipole and radial rings are specified at ±0.05 mm, and the one-piece body removes the segment-to-segment variation that shows up later as imbalance. Three items belong on the drawing: bore-to-shaft fit, pole-to-pole magnetic consistency after magnetization, and the absence of any glue line.

Segments remain a legitimate choice where the arc is defined rather than the ring. The 45SH segment example is OR32.5 × IR29 × H24.9 × 60°, diametrally magnetized, held to ±0.1 mm, and intended for permanent magnet BLDC motors for industrial pumps, servo motors for automation equipment, high-efficiency electric generators, HVAC fan motors, electric vehicle auxiliary motors and refrigeration compressor motors. A segment rotor needs a carrier and a bonding step; a one-piece ring does not, which is why the manufacturer frames the ring as a production-cost saving against assembled segment magnets.

Use Cases: Motors and Medical Devices

Motor and drive applications

The multipole and radial ring types are listed for high-precision magnetic encoders, small industrial BLDC servo motors, magnetic coupler and magnetic transmission assemblies, automotive auxiliary EPS motors, high-speed spindle motors for automation equipment, and precision magnetic speed sensors. That list is a useful map for engineers new to the category: the ring appears wherever the rotor is short, the pole count is fixed by the drive, and assembly cost matters as much as flux.

Larger machines use the same material logic at a different scale. Wind turbine generators are one example; published third-party estimates put NdFeB content for offshore wind at roughly 200–600 kg per MW of installed capacity, which makes grade consistency and batch documentation a procurement issue rather than a technical detail.

Automotive field application of sintered NdFeB magnets in auxiliary drive motors and sensors
Automotive auxiliary drives and sensors are a core application area for radially oriented and multipole sintered NdFeB rings.

Medical device applications

Medical work uses the same product families for different reasons: small size, repeatable field, and a documented supply chain. The N52 ring is positioned for medical device components alongside its motor and sensor uses, and the multipole and radial rings are listed for precision magnetic speed sensors and high-precision magnetic encoders — the position-feedback parts inside medical equipment drives. Medical imaging and device subsystems are also listed among the manufacturer's served project types.

What changes in a medical project is not the magnet physics but the evidence package: grade test reports, coating specification, dimensional records and a clear statement of which certificates cover which manufacturing steps.

Medical apparatus application using sintered NdFeB magnets in encoders, sensors and drive components
Medical apparatus: encoders, speed sensors and small drive components are the typical entry points for sintered NdFeB ring magnets.

Compliance Constraints: What the Certificates Actually Cover

For a first ring magnet project the compliance question is not 'are you certified' but 'what does the certificate cover'. Three certificates are relevant, and all three are issued against the sintered NdFeB manufacturing scope.

StandardCertificate numberIssuerValidityScope note
IATF 16949:201612 111 69512 TMS (IATF Cert. No. 0576974, USI L2S2NA)TÜV SÜD Management Service GmbH2025-07-04 to 2028-07-03Manufacturing of material and products for sintered NdFeB permanent magnets, without product design as per Chapter 8.3; applies to global and automotive export markets
ISO 9001:201512 100 69512 TMSTÜV SÜD Management Service GmbH2025-07-04 to 2028-07-03Manufacturing and sales of material and products for sintered NdFeB permanent magnets
ISO 14001:201502124E10013R1MHuaxia Certification Center, Inc.2024-01-02 to 2027-01-17Production and related management activities of sintered Nd-Fe-B permanent magnet and products

The IATF 16949 exclusion is the part engineers most often miss. Because the certificate excludes product design under Chapter 8.3, responsibility for the magnetic circuit — pole count, grade selection, working point — stays with the customer or is handled under a separate engineering agreement. The certificate confirms manufacturing process control, not design sign-off.

IATF 16949:2016 certificate issued to Ningbo Jinlun Magnet Technology by TUeV SUD for sintered NdFeB magnet manufacturing
IATF 16949:2016 certificate, issued by TÜV SÜD Management Service GmbH. Note the scope: manufacturing, without product design as per Chapter 8.3.

Step-by-Step: Specifying a Multipole Ring in Five Steps

  1. Fix the pole count and air gap before the magnet. The drive determines whether you need 4, 6, 8 or 12 poles; the ring is then sized around that pattern rather than the other way round.
  2. Convert measured magnet temperature into a grade. Take the temperature at the magnet, add margin, then pick the letter class: H at 120 °C, SH at 150 °C, UH at 180 °C, EH at 200 °C.
  3. Choose one-piece ring or segment assembly. A one-piece multipole or radial ring removes gluing, improves concentricity and dynamic balance, and simplifies rotor assembly; a defined arc geometry such as the 45SH OR32.5 × IR29 × H24.9 × 60° segment remains the alternative.
  4. Write tolerance, coating and magnetization on the drawing. ±0.05 mm for the ring, Ni-Cu-Ni as standard or zinc, epoxy, parylene for harsher environments, plus the pole pattern.
  5. Validate with samples and batch reports. Regular samples are quoted at 10 days and regular batches at 25 days, with a magnetic test report issued per batch.

Comparison Table: Four Sintered NdFeB Configurations

ConfigurationTypeDimensionsPolesBrHcj(BH)maxMax working temp.Tolerance
N52 ringRing, sintered NdFeBD20 × 10 × 5 mmNot specified in the listed configuration> 1.42 T> 955 kA/m398–422 kJ/m³80 °CPer drawing
42H multipole ringMultipole NdFeB ringOD25 × ID16 × H5 mm8 / 12> 1.29 T> 1353 kA/m318–342 kJ/m³120 °C (family up to 180 °C)±0.05 mm
40H radial ringRadially oriented NdFeB ringOD18 × ID10 × H4 mm4 / 6> 1.26 T> 1353 kA/m302–326 kJ/m³120 °C (N42H–N40UH up to 180 °C)±0.05 mm
45SH segmentSegment (arc) magnetOR32.5 × IR29 × H24.9 × 60°Diametral magnetization> 1.33 T> 1592 kA/m342–366 kJ/m³150 °C±0.1 mm

All values are manufacturer-published figures for the specific configurations listed. Other grades, dimensions, coatings and magnetization patterns are available to drawing.

FAQ

Which certifications should an IATF 16949 neodymium magnet manufacturer actually hold for a motor project?

Three certificates are relevant, and scope matters more than the logo. IATF 16949:2016 is the automotive quality management standard; JLmagnet's certificate is issued by TÜV SÜD Management Service GmbH under number 12 111 69512 TMS (IATF Cert. No. 0576974, USI L2S2NA), valid from 2025-07-04 to 2028-07-03, and covers manufacturing of material and products for sintered NdFeB permanent magnets without product design as per Chapter 8.3. ISO 9001:2015 (12 100 69512 TMS) covers quality management for the same manufacturing scope, and ISO 14001:2015 (02124E10013R1M, Huaxia Certification Center, Inc.) covers environmental management. Because the IATF scope excludes product design, magnetic circuit design responsibility normally stays with the customer or sits in a separate engineering agreement.

Can a one-piece multipole ring reach the working temperature of my motor?

Within the grade limits, yes. The multipole ring family is available in multiple grades with continuous operating temperature up to 180 °C, while the specific 42H OD25 × ID16 × H5 mm, 8/12-pole configuration is rated at 120 °C maximum working temperature. The radial ring offers grades from N42H to N40UH, which also reaches 180 °C. Standard sintered grade ceilings are 70–80 °C for N, 100 °C for M, 120 °C for H, 150 °C for SH, 180 °C for UH and 200 °C for EH, with AH grades quoted up to 220 °C in published third-party references. Specify against measured magnet temperature rather than housing temperature.

What drives the price of a sintered NdFeB ring magnet?

Five variables dominate: the grade, because higher coercivity classes and heavy rare-earth content such as Dy and Tb raise material cost — some formulations, such as the 38M block, use a non-heavy rare-earth formula with Dy/Tb content below 0.1%; the dimensions and wall thickness of the ring; the tolerance class, since ±0.05 mm requires more machining and inspection than ±0.1 mm; the coating, because Ni-Cu-Ni, zinc, epoxy and parylene involve different process steps; and the test documentation package. Volume and the choice between a one-piece ring and an assembled segment rotor also change the total cost of the assembly, not just the magnet.

How do I validate a ring magnet before committing to production?

Order samples against a drawing that already fixes pole count, grade, tolerance and coating. Regular samples are quoted at 10 days, and the minimum order quantity is 10 kg, with sample orders excluded and confirmed as needed. For the sintered NdFeB series the manufacturer quotes magnetic properties controlled within ±2% fluctuation, a 99.5% key dimensional pass rate and a magnetic test report issued per batch, which gives you the data needed to compare samples against the specification before releasing volume.

What lead times should I plan for?

Regular samples are quoted at 10 days and regular batches at 25 days. Monthly output is typically 600+ tons depending on order mix, with an annual capacity of 8,000 tons across four in-house bases covering sintering, machining, plating and testing. Delivery is confirmed per order, so the practical step is to share your pole pattern, grade and target temperature for a sample and quotation.

Conclusion

Multipole and radially oriented ring magnets are not a separate magnet category; they are sintered NdFeB shaped and magnetized so that a rotor can be built from one body instead of a glued segment stack. The benefits are mechanical as much as magnetic: concentricity and dynamic balance, stable pole-to-pole consistency, a smooth sinusoidal field for low torque ripple, and a simpler assembly. The constraints are equally concrete. Pole count, grade, tolerance and coating all have to be fixed on the drawing before a quotation means anything.

The N52 D20 × 10 × 5 mm ring shows the trade clearly: Br > 1.42 T and 398–422 kJ/m³, but a 955 kA/m intrinsic coercivity and an 80 °C ceiling, which keeps it in ambient duty. Raise the temperature and the same geometry has to move up the grade ladder — H at 120 °C, SH at 150 °C, UH at 180 °C, EH at 200 °C — accepting lower Br for higher Hcj. Once that ladder is understood, motor and medical device designs become a matter of matching grade, tolerance and documentation to the actual operating point.

Need a multipole or radial ring for your next build?

JLmagnet (Ningbo Jinlun Magnet Technology Co., Ltd.) produces sintered NdFeB rings, arcs, blocks and custom shapes, with grade, coating and magnetization specified to drawing. Samples, quotations and technical documentation are available on request.

Email: sales00@jlmagnet.com  |  Tel: +86-574-6321 2222  |  WhatsApp: +86 17621550719  |  www.jlmagnet.com

Download the 2026 company profile and product catalogue: JLmagnet Profile 2026 (PDF)

Magnet packing area preparing sintered NdFeB ring magnets for sample and batch shipment
Sample and batch packing area. Regular samples are quoted at 10 days; regular batches at 25 days.

Have Questions or Need More Details?

Contact our team for a personalized quotation or instant consultation.

Request a Quotation

Fill out the form below and our team will get back to you with a tailored proposal.

Attach images, files, or documents.

We'll respond within 24 hours (Mon–Sat).

WhatsApp Direct Chat

Prefer to chat in real-time? Message us on WhatsApp for instant assistance & quick answers.

  • Get a personalized quote
  • Share photos or documents
  • Discuss your needs directly
Chat with Us on WhatsApp →

Typically replies in 5–30 minutes during business hours.

Support: Images, videos, PDF
Latest